sa-1xx:pinmux_info:start
差分
この文書の現在のバージョンと選択したバージョンの差分を表示します。
| 両方とも前のリビジョン 前のリビジョン 次のリビジョン | 前のリビジョン | ||
|
sa-1xx:pinmux_info:start [2013/09/12 14:10] admin |
sa-1xx:pinmux_info:start [2013/09/12 15:06] (現在) admin |
||
|---|---|---|---|
| ライン 1: | ライン 1: | ||
| + | ====== PINマッピング ====== | ||
| + | |||
| + | ===== ポート名順 ===== | ||
| + | |||
| + | ^ Port Group ^ Port ^ Signal ^ Pull-Up/Pull-Down ^ Function ^ Description | | ||
| + | ^ PA |PA0|[XIO]PA0/WKUP|Internal Pull-UP|XIO| | | ||
| + | ^:::|PA1|ETH\_MII\_RX\_CLK| |ETHER 0| | | ||
| + | ^:::|PA2|ETH\_MDIO| |ETHER 0| | | ||
| + | ^:::|PA3|[XIO]A1| |XIO| | | ||
| + | ^:::|PA4|[XIO]SPI1\_NSS/ADC/DAC1\_OUT| |XIO| | | ||
| + | ^:::|PA5|[XIO]SPI1\_SCK/ADC/DAC2\_OUT| |XIO| | | ||
| + | ^:::|PA6|[XIO]SPI1\_MISO/ADC|Internal Pull-UP|XIO| | | ||
| + | ^:::|PA7|ETH\_MII\_RX\_DV| |ETHER 0| | | ||
| + | ^:::|PA8|MCO1| |System|PLL Clock output| | ||
| + | ^:::|PA9|OTG\_FS\_VBUS| |USB Device|USB Mini-B connector| | ||
| + | ^:::|PA10|OTG\_FS\_ID| |USB Device|USB Mini-B connector| | ||
| + | ^:::|PA11|OTG\_FS\_DM| |USB Device|USB Mini-B connector| | ||
| + | ^:::|PA12|OTG\_FS\_DP| |USB Device|USB Mini-B connector| | ||
| + | ^:::|PA13|JTMS-SWDIO| |JTAG| | | ||
| + | ^:::|PA14|JTCK-SWCLK| |JTAG| | | ||
| + | ^:::|PA15|JTDI| |JTAG| | | ||
| + | ^ PB |PB0|ETH\_MII\_RXD2| |ETHER 0| | | ||
| + | ^:::|PB1|ETH\_MII\_RXD3| |ETHER 0| | | ||
| + | ^:::|PB2|BOOT1| |System| | | ||
| + | ^:::|PB3|JTDO-SWO| |JTAG| | | ||
| + | ^:::|PB4|JTRST| |JTAG| | | ||
| + | ^:::|PB5|[XIO]SPI1\_MOSI| |XIO| | | ||
| + | ^:::|PB6|USART1\_TX| |Debug CONSOLE| | | ||
| + | ^:::|PB7|USART1\_RX| |Debug CONSOLE| | | ||
| + | ^:::|PB8|[XIO]I2C1\_SCL| |XIO| | | ||
| + | ^:::|PB9|[XIO]I2C1\_SDA|Internal Pull-UP|XIO| | | ||
| + | ^:::|PB10|ETH\_MII\_RX\_ER| |ETHER 0| | | ||
| + | ^:::|PB11|ETH\_MII\_TX\_EN| |ETHER 0| | | ||
| + | ^:::|PB12|ETH\_MII\_TXD0| |ETHER 0| | | ||
| + | ^:::|PB13|ETH\_MII\_TXD1| |ETHER 0| | | ||
| + | ^:::|PB14|[XIO]OTG\_HS\_DM| |XIO| | | ||
| + | ^:::|PB15|[XIO]OTG\_HS\_DP| |XIO| | | ||
| + | ^ PC |PC0|[XIO]PC0| |XIO| | | ||
| + | ^:::|PC1|ETH\_MDC| |ETHER 0| | | ||
| + | ^:::|PC2|ETH\_MII\_TXD2| |ETHER 0| | | ||
| + | ^:::|PC3|ETH\_MII\_TX\_CLK| |ETHER 0| | | ||
| + | ^:::|PC4|ETH\_MII\_RXD0| |ETHER 0| | | ||
| + | ^:::|PC5|ETH\_MII\_RXD1| |ETHER 0| | | ||
| + | ^:::|PC6|[XIO]TIM8-1| |XIO| | | ||
| + | ^:::|PC7|[XIO]TIM8-2| |XIO| | | ||
| + | ^:::|PC8|SDIO\_D0| |SD CARD| | | ||
| + | ^:::|PC9|SDIO\_D1| |SD CARD| | | ||
| + | ^:::|PC10|SDIO\_D2| |SD CARD| | | ||
| + | ^:::|PC11|SDIO\_D3| |SD CARD| | | ||
| + | ^:::|PC12|SDIO\_CK| |SD CARD| | | ||
| + | ^:::|PC13|RTC\_AF1| |System| | | ||
| + | ^:::|PC14|OSC32\_IN| |System| | | ||
| + | ^:::|PC15|OSC32\_OUT| |System| | | ||
| + | ^ PD |PD0|CAN1\_RX| |CAN|RX Data| | ||
| + | ^:::|PD1|CAN1\_TX| |CAN|TX Data| | ||
| + | ^:::|PD2|SDIO\_CMD| |SD CARD| | | ||
| + | ^:::|PD3|[XIO]USART2\_CTS|Internal Pull-UP|XIO| | | ||
| + | ^:::|PD4|[XIO]USART2\_RTS| |XIO| | | ||
| + | ^:::|PD5|[XIO]USART2\_TX| |XIO| | | ||
| + | ^:::|PD6|[XIO]USART2\_RX|Internal Pull-UP|XIO| | | ||
| + | ^:::|PD7|[XIO]USART2\_CK| |XIO| | | ||
| + | ^:::|PD8|USART3\_TX| |RS-232| | | ||
| + | ^:::|PD9|USART3\_RX| |RS-232| | | ||
| + | ^:::|PD10| | | | | ||
| + | ^:::|PD11|USART3\_CTS| |RS-232| | | ||
| + | ^:::|PD12|USART3\_RTS| |RS-232| | | ||
| + | ^:::|PD13| | | | | ||
| + | ^:::|PD14| | | | | ||
| + | ^:::|PD15| | | | | ||
| + | ^ PE |PE0| | | | | ||
| + | ^:::|PE1| | | | | ||
| + | ^:::|PE2|ETH\_MII\_TXD3| |ETHER 0| | | ||
| + | ^:::|PE3|DIO\_DO0| |DOUT CH0|Photo Coupler output| | ||
| + | ^:::|PE4|DIO\_DO1| |DOUT CH1|Photo Coupler output| | ||
| + | ^:::|PE5|DIO\_DO2| |DOUT CH2|Photo-MOS Relay output| | ||
| + | ^:::|PE6|DIO\_DO3| |DOUT CH3|Photo-MOS Relay output| | ||
| + | ^:::|PE7| | | | | ||
| + | ^:::|PE8|[XIO]TIM1\_CH1N| |XIO| | | ||
| + | ^:::|PE9|[XIO]TIM1\_CH1| |XIO| | | ||
| + | ^:::|PE10|MCU\_LED0\_G| | |Power LED Green (0=ON, 1=OFF)| | ||
| + | ^:::|PE11|MCU\_LED0\_R| | |Power LED Red (0=ON, 1=OFF)| | ||
| + | ^:::|PE12|MCU\_LED1\_G| | |Status1 LED Green (0=ON, 1=OFF)| | ||
| + | ^:::|PE13|MCU\_LED1\_R| | |Status1 LED Red (0=ON, 1=OFF)| | ||
| + | ^:::|PE14|MCU\_LED2\_G| | |Status2 LED Green (0=ON, 1=OFF)| | ||
| + | ^:::|PE15|MCU\_LED2\_R| | |Status2 LED Red (0=ON, 1=OFF)| | ||
| + | ^ PF |PF0|I2C2\_SDA| |I2C Devices|M24C16, LM77, RX-8025SA| | ||
| + | ^:::|PF1|I2C2\_SCL| |I2C Devices|M24C16, LM77, RX-8025SA| | ||
| + | ^:::|PF2| | | | | ||
| + | ^:::|PF3|[XIO]PF3| | | | ||
| + | ^:::|PF4|USART3\_FORCEON| |RS-232|RS-232 Transceiver Auto-power down mode (0=Enable, 1=Disable)| | ||
| + | ^:::|PF5|USART3\_FORCEOFF\_N| |RS-232|RS-232 Transceiver Power down (0=Power OFF, 1=Power ON)| | ||
| + | ^:::|PF6|USART3\_DTR| |RS-232| | | ||
| + | ^:::|PF7|USART3\_DSR| |RS-232| | | ||
| + | ^:::|PF8|USART3\_CD| |RS-232| | | ||
| + | ^:::|PF9|USART3\_RI| |RS-232| | | ||
| + | ^:::|PF10|USART3\_RI\_B| |RS-232|Noninverting RI (Always active)| | ||
| + | ^:::|PF11|MCU\_INITSW\_N| |INIT Switch| | ||
| + | ^:::|PF12|MCU\_DIPSW0| |DIP Switch[0] (0=OFF, 1=ON)| | ||
| + | ^:::|PF13|MCU\_DIPSW1| |DIP Switch[1] (0=OFF, 1=ON)| | ||
| + | ^:::|PF14|MCU\_DIPSW2| |DIP Switch[2] (0=OFF, 1=ON)| | ||
| + | ^:::|PF15|MCU\_DIPSW3| |MCU\_BOOT0 (DIP Switch[3])|System memory boot (DFU) (0=Flash Boot, 1=RAM Boot)| | ||
| + | ^ PG |PG0| | | | | ||
| + | ^:::|PG1| | | | | ||
| + | ^:::|PG2| | | | | ||
| + | ^:::|PG3| | | | | ||
| + | ^:::|PG4| | | | | ||
| + | ^:::|PG5| | | | | ||
| + | ^:::|PG6|SDIO\_CD\_SW| |SD CARD|SD SLOT Card detect| | ||
| + | ^:::|PG7|SDIO\_WP\_SW| |SD CARD|SD SLOT write protect switch| | ||
| + | ^:::|PG8|SDIO\_VDD\_ENB| | |SD SLOT Power enable| | ||
| + | ^:::|PG9|USART6\_RX| |RS-485|RX Data| | ||
| + | ^:::|PG10|USART6\_RCVENB\_N| |RS-485|Receiver Enable (0=Enable, 1=Disable)| | ||
| + | ^:::|PG11|USART6\_TCVENB| |RS-485|Transceiver Enable (0=Disable, 1=Enable)| | ||
| + | ^:::|PG12|USART6\_RTS| |RS-485|Reserved| | ||
| + | ^:::|PG13|CAN1\_STBY| |CAN|CAN Transceiver Enable (0=Enable, 1=Disable)| | ||
| + | ^:::|PG14|USART6\_TX| |RS-485|TX Data| | ||
| + | ^:::|PG15|USART6\_CTS| |RS-485|Reserved| | ||
| + | ^ PH |PH0|OSC\_IN| |8MHz External CLK| | | ||
| + | ^:::|PH1|OSC\_OUT| |8MHz External CLK| | | ||
| + | ^:::|PH2|ETH\_MII\_CRS| |ETHER 0| | | ||
| + | ^:::|PH3|ETH\_MII\_COL| |ETHER 0| | | ||
| + | ^:::|PH4|ETH\_RESET\_N| |ETHER 0|Ether PHY reset (0=Reset, 1=Normal)| | ||
| + | ^:::|PH5|ETH\_INTRP\_N| |ETHER 0|Ether PHY interrupt (0=Interrupt request)| | ||
| + | ^:::|PH6|ETH\_OSCENB\_N| |ETHER 0|Ether 25MHz OSC Enable (0=Disable, 1=Enable)| | ||
| + | ^:::|PH7| | | | | ||
| + | ^:::|PH8| | | | | ||
| + | ^:::|PH9| | | | | ||
| + | ^:::|PH10| | | |Reserved (errata)| | ||
| + | ^:::|PH11|[XIO]TIM5-2| |XIO| | | ||
| + | ^:::|PH12|[XIO]TIM5-3| |XIO| | | ||
| + | ^:::|PH13| | | | | ||
| + | ^:::|PH14| | | | | ||
| + | ^:::|PH15| | | | | ||
| + | ^ PI |PI0|SPI2\_NSS| |SPI FLASH| | | ||
| + | ^:::|PI1|SPI2\_SCK| |SPI FLASH| | | ||
| + | ^:::|PI2|SPI2\_MISO| |SPI FLASH| | | ||
| + | ^:::|PI3|SPI2\_MOSI| |SPI FLASH| | | ||
| + | ^:::|PI4|DIO\_IN0| |DIN CH0 (0=ON, 1=OFF)| | ||
| + | ^:::|PI5|DIO\_IN1| |DIN CH1 (0=ON, 1=OFF)| | ||
| + | ^:::|PI6|DIO\_IN2| |DIN CH2 (0=ON, 1=OFF)| | ||
| + | ^:::|PI7|DIO\_IN3| |DIN CH3 (0=ON, 1=OFF)| | ||
| + | ^:::|PI8|RTC\_AF2| | | | ||
| + | ^:::|PI9|I2C2\_INTB\_N| |I2C Devices|RTC RX-8025 Interrupt (0=Active)| | ||
| + | ^:::|PI10| | | |Reserved (eratta)| | ||
| + | ^:::|PI11|I2C2\_INTA\_N| |I2C Devices|LM77 Interrupt (0=Active)| | ||
| + | |||
| + | |||
| + | ===== 機能毎 ===== | ||
| + | |||
| + | ^ Function ^ Port ^ Signal Name ^ Mode ^ Direction ^ Pull-Up/Pull-Down ^ Description | | ||
| + | |8MHz External CLK|PH0|OSC\_IN|CLK| | |8MHz External Crystal input OR 8MHz OSC input| | ||
| + | |8MHz External CLK|PH1|OSC\_OUT|CLK| | |8MHz External Crystal output| | ||
| + | |System|PC14|OSC32\_IN|CLK| | |32.768kHz Crystal input OR 32.768kHz OSC input| | ||
| + | |System|PC15|OSC32\_OUT|CLK| | |32.768kHz Crystal output| | ||
| + | |System|PA8|MCO1|AF0|OUT| |HSI/LSE/HSE/PLL Clock output for DEBUG| | ||
| + | |JTAG|PA13|JTMS-SWDIO|SYS|I/O|external PU|JTAG TMS (SWDIO)| | ||
| + | |JTAG|PA14|JTCK-SWCLK|SYS|IN|external PD|JTAG TCK (SWCLK)| | ||
| + | |JTAG|PA15|JTDI|SYS|IN|external PU|JTAG TDI| | ||
| + | |JTAG|PB3|JTDO-SWO|SYS|OUT|external PU|JTAG TDO (SWO)| | ||
| + | |JTAG|PB4|JTRST|SYS|IN|external PU|JTAG TRST| | ||
| + | |Debug CONSOLE|PB6|USART1\_TX|AF7|OUT|external PU|CONSOLE TXD| | ||
| + | |Debug CONSOLE|PB7|USART1\_RX|AF7|IN|external PU|CONSOLE RXD| | ||
| + | |RS-232|PD8|USART3\_TX|AF7|OUT|external PU|RS-232 TXD| | ||
| + | |RS-232|PD9|USART3\_RX|AF7|IN|external PU|RS-232 RXD| | ||
| + | |RS-232|PD11|USART3\_CTS|AF7|IN|external PU|RS-232 CTS| | ||
| + | |RS-232|PD12|USART3\_RTS|AF7|OUT|external PU|RS-232 RTS| | ||
| + | |RS-232|PF6|USART3\_DTR|GPIO|OUT|external PU|RS-232 DTR| | ||
| + | |RS-232|PF7|USART3\_DSR|GPIO|IN|external PU|RS-232 DSR| | ||
| + | |RS-232|PF8|USART3\_CD|GPIO|IN|external PU|RS-232 CD| | ||
| + | |RS-232|PF9|USART3\_RI|GPIO|IN|external PU|RS-232 RI| | ||
| + | |RS-232|PF10|USART3\_RI\_B|GPIO|IRQ IN|Internal Pull-Down|RS-232 Noninverting RI[(トランシーバパワーダウン時も常にActiveで、RI信号によるウェイクアップ等に使用可能。)]| | ||
| + | |RS-232|PF4|USART3\_FORCEON|GPIO|OUT|external PD|RS-232 Transceiver Auto-power down mode[(ケーブル未接続で自動Power OFF)] (0=Enable, 1=Disable (Default Enable))| | ||
| + | |RS-232|PF5|USART3\_FORCEOFF\_N|GPIO|OUT|external PD|RS-232 Transceiver Power down (0=Power OFF, 1=Power ON (Default Power OFF))| | ||
| + | |RS-485|PG9|USART6\_RX|AF8|IN|external PU|RS-485 RXD| | ||
| + | |RS-485|PG10|USART6\_RCVENB\_N|GPIO|OUT|external PU|RS-485 Receiver Enable (0=Enable, 1=Disable (Default Disable))| | ||
| + | |RS-485|PG14|USART6\_TX|AF8|OUT|external PU|RS-485 TXD| | ||
| + | |RS-485|PG11|USART6\_TCVENB|GPIO|OUT|external PD|RS-485 Transceiver Enable (0=Disable, 1=Enable (Default Disable))| | ||
| + | |CAN|PD0|CAN1\_RX|AF9|IN|external PU|CAN RX Data| | ||
| + | |CAN|PD1|CAN1\_TX|AF9|OUT|external PU|CAN TX Data| | ||
| + | |CAN|PG13|CAN1\_STBY|GPIO|OUT|external PU|CAN Transceiver Enable (0=Enable, 1=Disable (Default Disable))| | ||
| + | |ETHER 0|PC1|ETH\_MDC|AF11|OUT| |Ether SMI Clock output| | ||
| + | |ETHER 0|PA2|ETH\_MDIO|AF11|I/O|external PU|Ether SMI Data IN/OUT| | ||
| + | |ETHER 0|PA1|ETH\_MII\_RX\_CLK|AF11|IN|Internal Pull-Down|Receive clock| | ||
| + | |ETHER 0|PA7|ETH\_MII\_RX\_DV|AF11|IN|external PD|RX DV| | ||
| + | |ETHER 0|PC4|ETH\_MII\_RXD0|AF11|IN|external PU|RX data[0]| | ||
| + | |ETHER 0|PC5|ETH\_MII\_RXD1|AF11|IN|external PD|RX data[1]| | ||
| + | |ETHER 0|PB0|ETH\_MII\_RXD2|AF11|IN|external PD|RX data[2]| | ||
| + | |ETHER 0|PB1|ETH\_MII\_RXD3|AF11|IN|external PU|RX data[3]| | ||
| + | |ETHER 0|PB10|ETH\_MII\_RX\_ER|AF11|IN|external PD|RX error| | ||
| + | |ETHER 0|PH2|ETH\_MII\_CRS|AF11|IN|external PD|Carrier sense| | ||
| + | |ETHER 0|PH3|ETH\_MII\_COL|AF11|IN|external PD|Collision| | ||
| + | |ETHER 0|PC3|ETH\_MII\_TX\_CLK|AF11|IN|Internal Pull-Down|Transmit clock| | ||
| + | |ETHER 0|PB11|ETH\_MII\_TX\_EN|AF11|OUT|external PD|TX EN (Pull-Down for DFU Boot)| | ||
| + | |ETHER 0|PB12|ETH\_MII\_TXD0|AF11|OUT| |TX data[0]| | ||
| + | |ETHER 0|PB13|ETH\_MII\_TXD1|AF11|OUT| |TX data[1]| | ||
| + | |ETHER 0|PC2|ETH\_MII\_TXD2|AF11|OUT| |TX data[2]| | ||
| + | |ETHER 0|PE2|ETH\_MII\_TXD3|AF11|OUT| |TX data[3]| | ||
| + | |ETHER 0 (PHY)|PH4|ETH\_RESET\_N|GPIO|OUT|external PD|Ether PHY Reset (0=Reset ON, 1=Reset OFF (Default Reset ON))| | ||
| + | |ETHER 0 (PHY)|PH5|ETH\_INTRP\_N|GPIO|IRQ IN|external PU|Ether PHY interrupt request (0=Active, 1=Inactive)| | ||
| + | |ETHER 0 (PHY)|PH6|ETH\_OSCENB\_N|GPIO|OUT|external PU|Ether 25MHz OSC Enable (0=Disable, 1=Enable (Default Enable))| | ||
| + | |USB Device|PA9|OTG\_FS\_VBUS|GPIO|IN|Internal Pull-UP|Not used| | ||
| + | |USB Device|PA10|OTG\_FS\_ID|GPIO|IN|external PU|Not used (Pull-up for DFU boot)| | ||
| + | |USB Device|PA11|OTG\_FS\_DM|AF10|I/O| |USB Mini-B connector / USB FS internal FS PHY Data-| | ||
| + | |USB Device|PA12|OTG\_FS\_DP|AF10|I/O| |USB Mini-B connector / USB FS internal FS PHY Data+| | ||
| + | |SD CARD|PC8|SDIO\_D0|AF12|I/O|external PU (SD+V)|SD CARD D0| | ||
| + | |SD CARD|PC9|SDIO\_D1|AF12|I/O|external PU (SD+V)|SD CARD D1| | ||
| + | |SD CARD|PC10|SDIO\_D2|AF12|I/O|external PU (SD+V)|SD CARD D2| | ||
| + | |SD CARD|PC11|SDIO\_D3|AF12|I/O|external PU (SD+V)|SD CARD D3| | ||
| + | |SD CARD|PC12|SDIO\_CK|AF12|OUT|external PU (SD+V)|SD CARD CLOCK| | ||
| + | |SD CARD|PD2|SDIO\_CMD|AF12|I/O|external PU (SD+V)|SD CARD COMMAND| | ||
| + | |SD CARD|PG6|SDIO\_CD\_SW|GPIO|IN|external PU|SD CARD Card Detect (0=Card IN, 1=Card OUT)| | ||
| + | |SD CARD|PG7|SDIO\_WP\_SW|GPIO|IN|external PU|SD CARD Write Protect switch (0=Write Protect, 1=Normal)| | ||
| + | |SD CARD|PG8|SDIO\_VDD\_ENB|GPIO|OUT|external PD|SD CARD Power enable (0=Power OFF, 1=Power ON (Default Power OFF))| | ||
| + | |SPI FLASH|PI0|SPI2\_NSS|AF5|OUT|external PU|N25Q064 Chip select| | ||
| + | |SPI FLASH|PI1|SPI2\_SCK|AF5|OUT|external PD|N25Q064 Clock| | ||
| + | |SPI FLASH|PI2|SPI2\_MISO|AF5|IN|external PU|N25Q064 Master IN/Serial OUT| | ||
| + | |SPI FLASH|PI3|SPI2\_MOSI|AF5|OUT|external PU|N25Q064 Master OUT/Serial IN| | ||
| + | |I2C Devices|PF0|I2C2\_SDA|AF4|I/O|external PU|M24C16, LM77, RX-8025SA| | ||
| + | |I2C Devices|PF1|I2C2\_SCL|AF4|OUT|external PU|M24C16, LM77, RX-8025SA| | ||
| + | |I2C Devices|PI9|I2C2\_INTB\_N|GPIO|IRQ IN|external PU|RTC RX-8025 Interrupt request (0=Active, 1=Inactive)| | ||
| + | |I2C Devices|PI11|I2C2\_INTA\_N|GPIO|IRQ IN|external PU|Temperature sensor LM77 Interrupt request (0=Active, 1=Inactive)| | ||
| + | |LED|PE10|MCU\_LED0\_G|GPIO|OUT|external PD|Power LED Green (0=ON, 1=OFF (default ON))| | ||
| + | |LED|PE11|MCU\_LED0\_R|GPIO|OUT| |Power LED Red (0=ON, 1=OFF)| | ||
| + | |LED|PE12|MCU\_LED1\_G|GPIO|OUT| |Status1 LED Green (0=ON, 1=OFF)| | ||
| + | |LED|PE13|MCU\_LED1\_R|GPIO|OUT| |Status1 LED Red (0=ON, 1=OFF)| | ||
| + | |LED|PE14|MCU\_LED2\_G|GPIO|OUT| |Status2 LED Green (0=ON, 1=OFF)| | ||
| + | |LED|PE15|MCU\_LED2\_R|GPIO|OUT| |Status2 LED Red (0=ON, 1=OFF)| | ||
| + | |INIT SWITCH|PF11|MCU\_INITSW\_N|GPIO|IRQ IN|external PU|INIT SWITCH (0=ON, 1=OFF)| | ||
| + | |DIP SWITCH|PF12|MCU\_DIPSW0|GPIO|IN|external PD|DIPSW[0] (0=OFF, 1=ON (注意：出力に設定すると壊れます))| | ||
| + | |DIP SWITCH|PF13|MCU\_DIPSW1|GPIO|IN|external PD|DIPSW[1] (0=OFF, 1=ON (注意：出力に設定すると壊れます))| | ||
| + | |DIP SWITCH|PF14|MCU\_DIPSW2|GPIO|IN|external PD|DIPSW[2] (0=OFF, 1=ON (注意：出力に設定すると壊れます))| | ||
| + | |MCU\_BOOT0|PF15|BOOT0/MCU\_DIPSW3|GPIO|IN|external PD|Boot mode[0] (0=Flash Boot, 1=RAM Boot) (boot up sequence)| | ||
| + | |DIP SITCH|:::|:::|:::|:::|:::|DIPSW[3] (0=OFF, 1=ON) (After boot up) (注意：出力に設定すると壊れます)| | ||
| + | |System|PB2|BOOT1|GPIO|IN|external PD|Boot mode[1] = Always 0| | ||
| + | |DIN|PI4|DIO\_IN0|GPIO|IN|external PU|DIN[0] (0=ON, 1=OFF (Default OFF))| | ||
| + | |DIN|PI5|DIO\_IN1|GPIO|IN|external PU|DIN[1] (0=ON, 1=OFF)| | ||
| + | |DIN|PI6|DIO\_IN2|GPIO|IN|external PU|DIN[2] (0=ON, 1=OFF)| | ||
| + | |DIN|PI7|DIO\_IN3|GPIO|IN|external PU|DIN[3] (0=ON, 1=OFF)| | ||
| + | |DOUT|PE3|DIO\_DO0|GPIO|OUT|external PU|DOUT[0] (0=ON, 1=OFF (Default OFF))| | ||
| + | |DOUT|PE4|DIO\_DO1|GPIO|OUT|external PU|DOUT[1] (0=ON, 1=OFF)| | ||
| + | |DOUT|PE5|DIO\_DO2|GPIO|OUT|external PU|DOUT[2] (0=ON, 1=OFF (Photo-MOS RELAY OUT))| | ||
| + | |DOUT|PE6|DIO\_DO3|GPIO|OUT|external PU|DOUT[3] (0=ON, 1=OFF (Photo-MOS RELAY OUT))| | ||
| + | |XIO|PA0|XIO\_PA0\_WKUP|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : ON/SLEEP# status (0=Sleep mode, 1=Wake up)| | ||
| + | |XIO|PA3|XIO\_PA3\_ADC|GPIO|OUT| |XBee S2B/S2C : DTR#/SLEEP\_RQ control (0=Wake up, 1=Pin sleep request)| | ||
| + | |XIO|PA4|SPI1\_NSS|AF5|OUT| |XBee S2B : Not used / S2C : SPI\_NSSEL| | ||
| + | |XIO|PA5|SPI1\_SCK|AF5|OUT| |XBee S2B : Not used / S2C : SPI\_CLK| | ||
| + | |XIO|PA6|SPI1\_MISO|AF5|IN|Internal Pull-UP|XBee S2B : Not used / S2C : SPI\_MISO| | ||
| + | |XIO|PB5|SPI1\_MOSI|AF5|OUT| |XBee S2B : Not used / S2C : SPI\_MOSI| | ||
| + | |XIO|PB8|I2C1\_SCL|AF4|OUT|Internal Pull-UP|Not used[(XBで未使用のピンはGPIO-IN, Internal Pull-UPの設定でも可)]| | ||
| + | |XIO|PB9|I2C1\_SDA|AF4|I/O|Internal Pull-UP|Not used| | ||
| + | |XIO|PB14|OTG\_HS\_DM|AF12|I/O|Internal Pull-UP|Not used| | ||
| + | |XIO|PB15|OTG\_HS\_DP|AF12|I/O|Internal Pull-UP|Not used| | ||
| + | |XIO|PC0|XIO\_PC0\_ADC|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : Associate LED[Green] status (Default)[(XBee moduleのAssociate LED機能をOFFにしてXBee[DIO5]=Inputとすることで、MCUからAssociate LEDの制御が可能となる。MCU[PC0]=GPIO OUT (0=ON, 1=OFF))]| | ||
| + | |XIO|PC6|XIO\_PC6|GPIO|OUT| |XBee S2B/S2C : RESET# control (0=Reset ON, 1=Reset OFF (Default OFF))| | ||
| + | |XIO|PC7|XIO\_PC7|GPIO|OUT| |XBee S2B/S2C : Power Enable (OPTION未実装) (0=OFF, 1=ON (Default ON))| | ||
| + | |XIO|PD3|USART2\_CTS|AF7|IN|Internal Pull-UP|XBee S2B/S2C : CTS# output| | ||
| + | |XIO|PD4|USART2\_RTS|AF7|OUT| |XBee S2B/S2C : RTS# input| | ||
| + | |XIO|PD5|USART2\_TX|AF7|OUT| |XBee S2B/S2C : DIN (serial rxd)| | ||
| + | |XIO|PD6|USART2\_RX|AF7|IN|Internal Pull-UP|XBee S2B/S2C : DOUT (serial txd)| | ||
| + | |XIO|PD7|USART2\_CK|GPIO|IN|Internal Pull-UP|Not used| | ||
| + | |XIO|PE8|XIO\_PE8|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : Commissioning Button status (0=ON, 1=OFF)| | ||
| + | |XIO|PE9|XIO\_PE9|GPIO|IN|Internal Pull-UP|XBee S2B : Not used / S2C : SPI\_ATTN#| | ||
| + | |XIO|PF3|XIO\_PF3\_ADC|GPIO|IN|Internal Pull-Down|XBee S2B/S2C : RSSI LED status (Default)[(XBee moduleのRSSI LED機能をOFFにしてXBee[DIO10]=Inputとすることで、MCUからRSSI LEDの制御が可能となる。MCU[PF3]=GPIO OUT (0=OFF, 1=ON))]| | ||
| + | |XIO|PH11|XIO\_PH11|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : DIO11/LED1[RED] control (通常は使用しない)| | ||
| + | |XIO|PH12|XIO\_PH12|GPIO|IN|Internal Pull-UP|Not used| | ||
| + | |Unused PIN|PG12|USART6\_RTS|GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PG15|USART6\_CTS|GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PC13|RTC\_AF1|GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PI8|RTC\_AF2|GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PD10| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PD13| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PD14| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PD15| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PE0| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PE1| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PE7| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PF2| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PG0| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PG1| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PG2| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PG3| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PG4| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PG5| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PH7| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PH8| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PH9| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PH12| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PH13| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PH14| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PH15| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |Unused PIN|PI10| |GPIO|IN|Internal Pull-Down|Not used| | ||
| + | |||
| + | ~~REFNOTES~~ | ||
sa-1xx/pinmux_info/start.1378962627.txt.bz2 · 最終更新: 2013/09/12 14:10 by admin
特に明示されていない限り、本Wikiの内容は次のライセンスに従います： CC Attribution-Share Alike 4.0 International
