この文書の現在のバージョンと選択したバージョンの差分を表示します。
両方とも前のリビジョン 前のリビジョン 次のリビジョン | 前のリビジョン | ||
mas1xx_ope:use_webui:wireless_module_setting:start [2021/04/02 15:55] admin |
mas1xx_ope:use_webui:wireless_module_setting:start [2021/04/05 07:57] (現在) admin |
||
---|---|---|---|
ライン 9: | ライン 9: | ||
===== 動作モード設定 ===== | ===== 動作モード設定 ===== | ||
- | 現状のドライバ・ファームウェアでは複数の無線規格を同時に使用すると安定しないので、使用する無線の種類をこの画面で選択します。 | + | 現状のドライバ・ファームウェアでは複数の無線規格を同時に使用すると安定しないので、使用する無線の種類をこの画面で選択します。\\ |
+ | Module が WirelessLAN で使用中の場合、モード変更はできません。 | ||
+ | |||
+ | {{:mas1xx_ope:use_webui:wireless_module_setting:wireless_module_mode_01.png?1280|Module 使用中のため動作モード変更不可}} | ||
\\ | \\ | ||
ライン 46: | ライン 49: | ||
\\ | \\ | ||
+ | |||
+ | {{:mas1xx_ope:use_webui:wireless_module_setting:wireless_module_network_station_01.png?1280|SSID検索 確認ダイアログ}} | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{:mas1xx_ope:use_webui:wireless_module_setting:wireless_module_network_station_02.png?1280|SSID 検索中}} | ||
+ | |||
+ | \\ | ||
+ | |||
+ | 検索が完了したら、『SSID 選択』のプルダウンメニューから接続する SSID を選択し、パスフレーズを入力して 『設定』をクリックします。\\ | ||
+ | "ifup Method" は普通の AccessPoint に接続する場合、"DHCP" を選択します。 | ||
+ | |||
+ | {{:mas1xx_ope:use_webui:wireless_module_setting:wireless_module_network_station_03.png?1280|WPA Passphrase 入力}} | ||
+ | |||
+ | \\ | ||
+ | |||
+ | 設定が完了しましたが、次回機器の起動時に自動で接続されるように設定されただけなので、今すぐ接続したい場合は 『起動』をクリックします。 | ||
+ | |||
+ | {{:mas1xx_ope:use_webui:wireless_module_setting:wireless_module_network_station_04.png?1280|WirelessLAN 接続}} | ||
+ | |||
+ | \\ | ||
+ | |||
+ | 接続ができると、ステータスが 『動作中』『接続中』になります。 | ||
+ | |||
+ | {{:mas1xx_ope:use_webui:wireless_module_setting:wireless_module_network_station_05.png?1280|Station 接続完了}} | ||
+ | |||
+ | \\ | ||
+ | |||
+ | === 生成される設定ファイル === | ||
+ | |||
+ | Station にした場合、下記 2 つの設定ファイル((ファイル内容サンプルです))が生成されます。 | ||
+ | |||
+ | * **/etc/network/interfaces.d/wlan0** | ||
+ | |||
+ | <file config wlan0> | ||
+ | allow-hotplug wlan0 | ||
+ | iface wlan0 inet dhcp | ||
+ | wpa-conf /etc/wpa_supplicant/wlan0.conf | ||
+ | </file> | ||
+ | |||
+ | * **/etc/wpa_supplicant/wlan0.conf** | ||
+ | |||
+ | <file config wlan0.conf> | ||
+ | p2p_disabled=1 | ||
+ | network={ | ||
+ | ssid="Buffalo-A-xxxx" | ||
+ | psk=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx | ||
+ | } | ||
+ | </file> | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ===== AccessPoint 設定 ===== | ||
+ | |||
+ | * [[.hostapd_settings:start]] | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ===== ステータス表示 ===== | ||
+ | |||
+ | * [[.wlan_status:start]] | ||
+ | |||
+ | \\ | ||
+ | |||