差分

この文書の現在のバージョンと選択したバージョンの差分を表示します。

--- mae3xx_tips:setup_ser2net:start [2014/09/04 17:29]
admin
+++ mae3xx_tips:setup_ser2net:start [2014/09/04 17:32] (現在)
admin
@@ ライン 1: / ライン 1: @@
+====== ser2net を使う (RFC-2217 対応 COM Port Redirecter) ======
+[[mae3xx_tips:use_socat:start]] で紹介した socat を使用する場合、シリアルポートの設定(ビットレート、キャラクタバイト数など)を変更することはできません。\\
+シリアルポートの設定変更に対応したプロトコルとして [[http://tools.ietf.org/html/rfc2217|RFC-2217 - Telnet Com Port Control Option]] というものが策定されており、それに対応したアプリケーションが [[http://ser2net.sourceforge.net/|ser2net]] です。
+\\
+===== 設定 =====
+/etc/ser2net.conf ファイルを作成・編集します。\\
+サンプルファイルとして、/etc/ser2net.conf.example というファイルが入っていますので、それを変更して作成すると楽です。
+<file conf ser2net.conf.example>
+#
+# This is the configuration file for ser2net.  It has the following format:
+#  <TCP port>:<state>:<timeout>:<device>:<options>
+#     TCP port
+#            Name   or  number of the TCP/IP port to accept con-
+#            nections from for this device.  A port number may
+#            be of the form [host,]port, such as 127.0.0.1,2000
+#            or localhost,2000.  If this is specified, it will
+#            only bind to the IP address specified. Otherwise
+#            it will bind to all the ports on the machine.
+#
+#     state  Either raw or rawlp or telnet or off.  off disables
+#            the  port  from  accepting  connections.  It can be
+#            turned on later from the control port.  raw enables
+#            the port and  transfers  all data as-is between the
+#            port  and  the long.  rawlp  enables  the port  and
+#            transfers  all input data to device, device is open
+#            without  any  termios  setting.  It  allow  to  use
+#            /dev/lpX  devices  and  printers connected to them.
+#            telnet enables the port and runs the telnet  proto-
+#            col  on the port to set up telnet parameters.  This
+#            is most useful for using telnet.
+#
+#     timeout
+#            The time (in seconds) before the port will be  dis-
+#            connected  if  there  is no activity on it.  A zero
+#            value disables this funciton.
+#
+#     device The  name  of  the  device   to  connect  to.  This
+#            must be in the form of /dev/<device>.
+#
+#     options
+#            Sets  operational  parameters  for the serial port.
+#            Options 300, 1200, 2400, 4800, 9600, 19200, 38400,
+#            57600, 115200 set the various baud rates.  EVEN,
+#            ODD, NONE set the parity.  1STOPBIT, 2STOPBITS set
+#            the number of stop bits.  7DATABITS, 8DATABITS set
+#            the number of data bits.  [-]XONXOFF turns on (-
+#            off) XON/XOFF support.  [-]RTSCTS turns on (- off)
+#            hardware flow control, [-]LOCAL turns off (- on)
+#            monitoring of the modem lines, and
+#            [-]HANGUP_WHEN_DONE turns on (- off) lowering the
+#            modem control lines when the connextion is done.
+#	     NOBREAK disables automatic setting of the break
+#	     setting of the serial port.
+#            The "remctl" option allow remote control (ala RFC
+#            2217) of serial-port configuration.  A banner name
+#            may also be specified, that banner will be printed
+#            for the line.  If no banner is given, then no
+#            banner is printed.
+#
+# or...
+#  BANNER:<banner name>:banner
+#    This will create a banner, if the banner name is given in the
+#    options of a line, that banner will be printed.  This takes the
+#    standard "C" \x characters (\r is carraige return, \n is newline,
+#    etc.).  It also accepts \d, which prints the device name, \p,
+#    which prints the TCP port number, and \s which prints the serial
+#    parameters (eg 9600N81).  Banners can span lines if the last
+#    character on a line is '\'.  Note that you *must* use \r\n to
+#    start a new line.
+#
+# Note that the same device can be listed multiple times under different
+# ports, this allows the same serial port to have both telnet and raw
+# protocols.
+# The original config file shipped with the upstream sources can be
+# found in /usr/share/doc/ser2net/examples
+BANNER:banner:\r\nser2net port \p device \d [\s] (Debian GNU/Linux)\r\n\r\n
+:telnet:600:/dev/ttyS0:9600 8DATABITS NONE 1STOPBIT banner
+:telnet:600:/dev/ttyS1:9600 8DATABITS NONE 1STOPBIT banner
+:telnet:600:/dev/ttyS0:19200 8DATABITS NONE 1STOPBIT banner
+:telnet:600:/dev/ttyS1:19200 8DATABITS NONE 1STOPBIT banner
+</file>
+\\
+===== ドライバ =====
+Windows からアクセスするためのドライバもあります。
+=== HW VSP3 ===
+[[http://www.hw-group.com/products/hw_vsp/index_en.html|{{http://www.hw-group.com/products/hw_vsp/images/HW_VSP3_overview_250.png|HW VSP3 - Virtual Serial Port}}]]
+  * [[http://www.hw-group.com/products/hw_vsp/index_en.html|HW VSP3 - Virtual Serial Port]]
+== Features (抜粋) ==
+  * Free, unrestricted Virtual Serial Port driver for any TCP/IP devices
+  * Compatible with Windows 2000, XP (Win 98, NT), Windows 8 & even 32-bit or 64 bit.
+  * Runs as a standalone application, or as a NT service suitable for servers
+  * This software is FREEWARE, as long as you comply with the license terms and conditions
+**64bit** にも対応しているという点がいいですね。
+\\
+=== Null-modem emulator (com0com) ===
+  * [[http://com0com.sourceforge.net/]]

MA-X/MA-S/MA-E/IP-K Developers' WiKi

ユーザ用ツール

サイト用ツール

差分

ページ用ツール