====== PINマッピング ======

===== ポート名順 =====

^  Port Group  ^  Port  ^  Signal  ^  Pull-Up/Pull-Down  ^  Function  ^  Description  |
^  PA  |PA0|[XIO]PA0/WKUP|Internal Pull-UP|XIO| |
^:::|PA1|ETH\_MII\_RX\_CLK| |ETHER 0| |
^:::|PA2|ETH\_MDIO| |ETHER 0| |
^:::|PA3|[XIO]A1| |XIO| |
^:::|PA4|[XIO]SPI1\_NSS/ADC/DAC1\_OUT| |XIO| |
^:::|PA5|[XIO]SPI1\_SCK/ADC/DAC2\_OUT| |XIO| |
^:::|PA6|[XIO]SPI1\_MISO/ADC|Internal Pull-UP|XIO| |
^:::|PA7|ETH\_MII\_RX\_DV| |ETHER 0| |
^:::|PA8|MCO1| |System|PLL Clock output|
^:::|PA9|OTG\_FS\_VBUS| |USB Device|USB Mini-B connector|
^:::|PA10|OTG\_FS\_ID| |USB Device|USB Mini-B connector|
^:::|PA11|OTG\_FS\_DM| |USB Device|USB Mini-B connector|
^:::|PA12|OTG\_FS\_DP| |USB Device|USB Mini-B connector|
^:::|PA13|JTMS-SWDIO| |JTAG| |
^:::|PA14|JTCK-SWCLK| |JTAG| |
^:::|PA15|JTDI| |JTAG| |
^  PB  |PB0|ETH\_MII\_RXD2| |ETHER 0| |
^:::|PB1|ETH\_MII\_RXD3| |ETHER 0| |
^:::|PB2|BOOT1| |System| |
^:::|PB3|JTDO-SWO| |JTAG| |
^:::|PB4|JTRST| |JTAG| |
^:::|PB5|[XIO]SPI1\_MOSI| |XIO| |
^:::|PB6|USART1\_TX| |Debug CONSOLE| |
^:::|PB7|USART1\_RX| |Debug CONSOLE| |
^:::|PB8|[XIO]I2C1\_SCL| |XIO| |
^:::|PB9|[XIO]I2C1\_SDA|Internal Pull-UP|XIO| |
^:::|PB10|ETH\_MII\_RX\_ER| |ETHER 0| |
^:::|PB11|ETH\_MII\_TX\_EN| |ETHER 0| |
^:::|PB12|ETH\_MII\_TXD0| |ETHER 0| |
^:::|PB13|ETH\_MII\_TXD1| |ETHER 0| |
^:::|PB14|[XIO]OTG\_HS\_DM| |XIO| |
^:::|PB15|[XIO]OTG\_HS\_DP| |XIO| |
^  PC  |PC0|[XIO]PC0| |XIO| |
^:::|PC1|ETH\_MDC| |ETHER 0| |
^:::|PC2|ETH\_MII\_TXD2| |ETHER 0| |
^:::|PC3|ETH\_MII\_TX\_CLK| |ETHER 0| |
^:::|PC4|ETH\_MII\_RXD0| |ETHER 0| |
^:::|PC5|ETH\_MII\_RXD1| |ETHER 0| |
^:::|PC6|[XIO]TIM8-1| |XIO| |
^:::|PC7|[XIO]TIM8-2| |XIO| |
^:::|PC8|SDIO\_D0| |SD CARD| |
^:::|PC9|SDIO\_D1| |SD CARD| |
^:::|PC10|SDIO\_D2| |SD CARD| |
^:::|PC11|SDIO\_D3| |SD CARD| |
^:::|PC12|SDIO\_CK| |SD CARD| |
^:::|PC13|RTC\_AF1| |System| |
^:::|PC14|OSC32\_IN| |System| |
^:::|PC15|OSC32\_OUT| |System| |
^  PD  |PD0|CAN1\_RX| |CAN|RX Data|
^:::|PD1|CAN1\_TX| |CAN|TX Data|
^:::|PD2|SDIO\_CMD| |SD CARD| |
^:::|PD3|[XIO]USART2\_CTS|Internal Pull-UP|XIO| |
^:::|PD4|[XIO]USART2\_RTS| |XIO| |
^:::|PD5|[XIO]USART2\_TX| |XIO| |
^:::|PD6|[XIO]USART2\_RX|Internal Pull-UP|XIO| |
^:::|PD7|[XIO]USART2\_CK| |XIO| |
^:::|PD8|USART3\_TX| |RS-232| |
^:::|PD9|USART3\_RX| |RS-232| |
^:::|PD10| | | |
^:::|PD11|USART3\_CTS| |RS-232| |
^:::|PD12|USART3\_RTS| |RS-232| |
^:::|PD13| | | |
^:::|PD14| | | |
^:::|PD15| | | |
^  PE  |PE0| | | |
^:::|PE1| | | |
^:::|PE2|ETH\_MII\_TXD3| |ETHER 0| |
^:::|PE3|DIO\_DO0| |DOUT CH0|Photo Coupler output|
^:::|PE4|DIO\_DO1| |DOUT CH1|Photo Coupler output|
^:::|PE5|DIO\_DO2| |DOUT CH2|Photo-MOS Relay output|
^:::|PE6|DIO\_DO3| |DOUT CH3|Photo-MOS Relay output|
^:::|PE7| | | |
^:::|PE8|[XIO]TIM1\_CH1N| |XIO| |
^:::|PE9|[XIO]TIM1\_CH1| |XIO| |
^:::|PE10|MCU\_LED0\_G| | |Power LED Green (0=ON, 1=OFF)|
^:::|PE11|MCU\_LED0\_R| | |Power LED Red   (0=ON, 1=OFF)|
^:::|PE12|MCU\_LED1\_G| | |Status1 LED Green (0=ON, 1=OFF)|
^:::|PE13|MCU\_LED1\_R| | |Status1 LED Red   (0=ON, 1=OFF)|
^:::|PE14|MCU\_LED2\_G| | |Status2 LED Green (0=ON, 1=OFF)|
^:::|PE15|MCU\_LED2\_R| | |Status2 LED Red   (0=ON, 1=OFF)|
^  PF  |PF0|I2C2\_SDA| |I2C Devices|M24C16, LM77, RX-8025SA|
^:::|PF1|I2C2\_SCL| |I2C Devices|M24C16, LM77, RX-8025SA|
^:::|PF2| | | |
^:::|PF3|[XIO]PF3| | |
^:::|PF4|USART3\_FORCEON| |RS-232|RS-232 Transceiver Auto-power down mode (0=Enable, 1=Disable)|
^:::|PF5|USART3\_FORCEOFF\_N| |RS-232|RS-232 Transceiver Power down (0=Power OFF, 1=Power ON)|
^:::|PF6|USART3\_DTR| |RS-232| |
^:::|PF7|USART3\_DSR| |RS-232| |
^:::|PF8|USART3\_CD| |RS-232| |
^:::|PF9|USART3\_RI| |RS-232| |
^:::|PF10|USART3\_RI\_B| |RS-232|Noninverting RI (Always active)|
^:::|PF11|MCU\_INITSW\_N| |INIT Switch|
^:::|PF12|MCU\_DIPSW0| |DIP Switch[0] (0=OFF, 1=ON)|
^:::|PF13|MCU\_DIPSW1| |DIP Switch[1] (0=OFF, 1=ON)|
^:::|PF14|MCU\_DIPSW2| |DIP Switch[2] (0=OFF, 1=ON)|
^:::|PF15|MCU\_DIPSW3| |MCU\_BOOT0 (DIP Switch[3])|System memory boot (DFU) (0=Flash Boot, 1=RAM Boot)|
^  PG  |PG0| | | |
^:::|PG1| | | |
^:::|PG2| | | |
^:::|PG3| | | |
^:::|PG4| | | |
^:::|PG5| | | |
^:::|PG6|SDIO\_CD\_SW| |SD CARD|SD SLOT Card detect|
^:::|PG7|SDIO\_WP\_SW| |SD CARD|SD SLOT write protect switch|
^:::|PG8|SDIO\_VDD\_ENB| | |SD SLOT Power enable|
^:::|PG9|USART6\_RX| |RS-485|RX Data|
^:::|PG10|USART6\_RCVENB\_N| |RS-485|Receiver Enable (0=Enable, 1=Disable)|
^:::|PG11|USART6\_TCVENB| |RS-485|Transceiver Enable (0=Disable, 1=Enable)|
^:::|PG12|USART6\_RTS| |RS-485|Reserved|
^:::|PG13|CAN1\_STBY| |CAN|CAN Transceiver Enable (0=Enable, 1=Disable)|
^:::|PG14|USART6\_TX| |RS-485|TX Data|
^:::|PG15|USART6\_CTS| |RS-485|Reserved|
^  PH  |PH0|OSC\_IN| |8MHz External CLK| |
^:::|PH1|OSC\_OUT| |8MHz External CLK| |
^:::|PH2|ETH\_MII\_CRS| |ETHER 0| |
^:::|PH3|ETH\_MII\_COL| |ETHER 0| |
^:::|PH4|ETH\_RESET\_N| |ETHER 0|Ether PHY reset (0=Reset, 1=Normal)|
^:::|PH5|ETH\_INTRP\_N| |ETHER 0|Ether PHY interrupt (0=Interrupt request)|
^:::|PH6|ETH\_OSCENB\_N| |ETHER 0|Ether 25MHz OSC Enable (0=Disable, 1=Enable)|
^:::|PH7| | | |
^:::|PH8| | | |
^:::|PH9| | | |
^:::|PH10| | | |Reserved (errata)|
^:::|PH11|[XIO]TIM5-2| |XIO| |
^:::|PH12|[XIO]TIM5-3| |XIO| |
^:::|PH13| | | |
^:::|PH14| | | |
^:::|PH15| | | |
^  PI  |PI0|SPI2\_NSS| |SPI FLASH| |
^:::|PI1|SPI2\_SCK| |SPI FLASH| |
^:::|PI2|SPI2\_MISO| |SPI FLASH| |
^:::|PI3|SPI2\_MOSI| |SPI FLASH| |
^:::|PI4|DIO\_IN0| |DIN CH0 (0=ON, 1=OFF)|
^:::|PI5|DIO\_IN1| |DIN CH1 (0=ON, 1=OFF)|
^:::|PI6|DIO\_IN2| |DIN CH2 (0=ON, 1=OFF)|
^:::|PI7|DIO\_IN3| |DIN CH3 (0=ON, 1=OFF)|
^:::|PI8|RTC\_AF2| | |
^:::|PI9|I2C2\_INTB\_N| |I2C Devices|RTC RX-8025 Interrupt (0=Active)|
^:::|PI10| | | |Reserved (eratta)|
^:::|PI11|I2C2\_INTA\_N| |I2C Devices|LM77 Interrupt (0=Active)|


===== 機能毎 =====

^  Function  ^  Port  ^  Signal Name  ^  Mode  ^  Direction  ^  Pull-Up/Pull-Down  ^  Description  |
|8MHz External CLK|PH0|OSC\_IN|CLK| | |8MHz External Crystal input OR 8MHz OSC input|
|8MHz External CLK|PH1|OSC\_OUT|CLK| | |8MHz External Crystal output|
|System|PC14|OSC32\_IN|CLK| | |32.768kHz Crystal input OR 32.768kHz OSC input|
|System|PC15|OSC32\_OUT|CLK| | |32.768kHz Crystal output|
|System|PA8|MCO1|AF0|OUT| |HSI/LSE/HSE/PLL Clock output for DEBUG|
|JTAG|PA13|JTMS-SWDIO|SYS|I/O|external PU|JTAG TMS (SWDIO)|
|JTAG|PA14|JTCK-SWCLK|SYS|IN|external PD|JTAG TCK (SWCLK)|
|JTAG|PA15|JTDI|SYS|IN|external PU|JTAG TDI|
|JTAG|PB3|JTDO-SWO|SYS|OUT|external PU|JTAG TDO (SWO)|
|JTAG|PB4|JTRST|SYS|IN|external PU|JTAG TRST|
|Debug CONSOLE|PB6|USART1\_TX|AF7|OUT|external PU|CONSOLE TXD|
|Debug CONSOLE|PB7|USART1\_RX|AF7|IN|external PU|CONSOLE RXD|
|RS-232|PD8|USART3\_TX|AF7|OUT|external PU|RS-232 TXD|
|RS-232|PD9|USART3\_RX|AF7|IN|external PU|RS-232 RXD|
|RS-232|PD11|USART3\_CTS|AF7|IN|external PU|RS-232 CTS|
|RS-232|PD12|USART3\_RTS|AF7|OUT|external PU|RS-232 RTS|
|RS-232|PF6|USART3\_DTR|GPIO|OUT|external PU|RS-232 DTR|
|RS-232|PF7|USART3\_DSR|GPIO|IN|external PU|RS-232 DSR|
|RS-232|PF8|USART3\_CD|GPIO|IN|external PU|RS-232 CD|
|RS-232|PF9|USART3\_RI|GPIO|IN|external PU|RS-232 RI|
|RS-232|PF10|USART3\_RI\_B|GPIO|IRQ IN|Internal Pull-Down|RS-232 Noninverting RI[(トランシーバパワーダウン時も常にActiveで、RI信号によるウェイクアップ等に使用可能。)]|
|RS-232|PF4|USART3\_FORCEON|GPIO|OUT|external PD|RS-232 Transceiver Auto-power down mode[(ケーブル未接続で自動Power OFF)] (0=Enable, 1=Disable (Default Enable))|
|RS-232|PF5|USART3\_FORCEOFF\_N|GPIO|OUT|external PD|RS-232 Transceiver Power down (0=Power OFF, 1=Power ON (Default Power OFF))|
|RS-485|PG9|USART6\_RX|AF8|IN|external PU|RS-485 RXD|
|RS-485|PG10|USART6\_RCVENB\_N|GPIO|OUT|external PU|RS-485 Receiver Enable (0=Enable, 1=Disable (Default Disable))|
|RS-485|PG14|USART6\_TX|AF8|OUT|external PU|RS-485 TXD|
|RS-485|PG11|USART6\_TCVENB|GPIO|OUT|external PD|RS-485 Transceiver Enable (0=Disable, 1=Enable (Default Disable))|
|CAN|PD0|CAN1\_RX|AF9|IN|external PU|CAN RX Data|
|CAN|PD1|CAN1\_TX|AF9|OUT|external PU|CAN TX Data|
|CAN|PG13|CAN1\_STBY|GPIO|OUT|external PU|CAN Transceiver Enable (0=Enable, 1=Disable (Default Disable))|
|ETHER 0|PC1|ETH\_MDC|AF11|OUT| |Ether SMI Clock output|
|ETHER 0|PA2|ETH\_MDIO|AF11|I/O|external PU|Ether SMI Data IN/OUT|
|ETHER 0|PA1|ETH\_MII\_RX\_CLK|AF11|IN|Internal Pull-Down|Receive clock|
|ETHER 0|PA7|ETH\_MII\_RX\_DV|AF11|IN|external PD|RX DV|
|ETHER 0|PC4|ETH\_MII\_RXD0|AF11|IN|external PU|RX data[0]|
|ETHER 0|PC5|ETH\_MII\_RXD1|AF11|IN|external PD|RX data[1]|
|ETHER 0|PB0|ETH\_MII\_RXD2|AF11|IN|external PD|RX data[2]|
|ETHER 0|PB1|ETH\_MII\_RXD3|AF11|IN|external PU|RX data[3]|
|ETHER 0|PB10|ETH\_MII\_RX\_ER|AF11|IN|external PD|RX error|
|ETHER 0|PH2|ETH\_MII\_CRS|AF11|IN|external PD|Carrier sense|
|ETHER 0|PH3|ETH\_MII\_COL|AF11|IN|external PD|Collision|
|ETHER 0|PC3|ETH\_MII\_TX\_CLK|AF11|IN|Internal Pull-Down|Transmit clock|
|ETHER 0|PB11|ETH\_MII\_TX\_EN|AF11|OUT|external PD|TX EN (Pull-Down for DFU Boot)|
|ETHER 0|PB12|ETH\_MII\_TXD0|AF11|OUT| |TX data[0]|
|ETHER 0|PB13|ETH\_MII\_TXD1|AF11|OUT| |TX data[1]|
|ETHER 0|PC2|ETH\_MII\_TXD2|AF11|OUT| |TX data[2]|
|ETHER 0|PE2|ETH\_MII\_TXD3|AF11|OUT| |TX data[3]|
|ETHER 0 (PHY)|PH4|ETH\_RESET\_N|GPIO|OUT|external PD|Ether PHY Reset (0=Reset ON, 1=Reset OFF (Default Reset ON))|
|ETHER 0 (PHY)|PH5|ETH\_INTRP\_N|GPIO|IRQ IN|external PU|Ether PHY interrupt request (0=Active, 1=Inactive)|
|ETHER 0 (PHY)|PH6|ETH\_OSCENB\_N|GPIO|OUT|external PU|Ether 25MHz OSC Enable (0=Disable, 1=Enable (Default Enable))|
|USB Device|PA9|OTG\_FS\_VBUS|GPIO|IN|Internal Pull-UP|Not used|
|USB Device|PA10|OTG\_FS\_ID|GPIO|IN|external PU|Not used (Pull-up for DFU boot)|
|USB Device|PA11|OTG\_FS\_DM|AF10|I/O| |USB Mini-B connector / USB FS internal FS PHY Data-|
|USB Device|PA12|OTG\_FS\_DP|AF10|I/O| |USB Mini-B connector / USB FS internal FS PHY Data+|
|SD CARD|PC8|SDIO\_D0|AF12|I/O|external PU (SD+V)|SD CARD D0|
|SD CARD|PC9|SDIO\_D1|AF12|I/O|external PU (SD+V)|SD CARD D1|
|SD CARD|PC10|SDIO\_D2|AF12|I/O|external PU (SD+V)|SD CARD D2|
|SD CARD|PC11|SDIO\_D3|AF12|I/O|external PU (SD+V)|SD CARD D3|
|SD CARD|PC12|SDIO\_CK|AF12|OUT|external PU (SD+V)|SD CARD CLOCK|
|SD CARD|PD2|SDIO\_CMD|AF12|I/O|external PU (SD+V)|SD CARD COMMAND|
|SD CARD|PG6|SDIO\_CD\_SW|GPIO|IN|external PU|SD CARD Card Detect (0=Card IN, 1=Card OUT)|
|SD CARD|PG7|SDIO\_WP\_SW|GPIO|IN|external PU|SD CARD Write Protect switch (0=Write Protect, 1=Normal)|
|SD CARD|PG8|SDIO\_VDD\_ENB|GPIO|OUT|external PD|SD CARD Power enable (0=Power OFF, 1=Power ON (Default Power OFF))|
|SPI FLASH|PI0|SPI2\_NSS|AF5|OUT|external PU|N25Q064 Chip select|
|SPI FLASH|PI1|SPI2\_SCK|AF5|OUT|external PD|N25Q064 Clock|
|SPI FLASH|PI2|SPI2\_MISO|AF5|IN|external PU|N25Q064 Master IN/Serial OUT|
|SPI FLASH|PI3|SPI2\_MOSI|AF5|OUT|external PU|N25Q064 Master OUT/Serial IN|
|I2C Devices|PF0|I2C2\_SDA|AF4|I/O|external PU|M24C16, LM77, RX-8025SA|
|I2C Devices|PF1|I2C2\_SCL|AF4|OUT|external PU|M24C16, LM77, RX-8025SA|
|I2C Devices|PI9|I2C2\_INTB\_N|GPIO|IRQ IN|external PU|RTC RX-8025 Interrupt request (0=Active, 1=Inactive)|
|I2C Devices|PI11|I2C2\_INTA\_N|GPIO|IRQ IN|external PU|Temperature sensor LM77 Interrupt request (0=Active, 1=Inactive)|
|LED|PE10|MCU\_LED0\_G|GPIO|OUT|external PD|Power LED Green (0=ON, 1=OFF (default ON))|
|LED|PE11|MCU\_LED0\_R|GPIO|OUT| |Power LED Red (0=ON, 1=OFF)|
|LED|PE12|MCU\_LED1\_G|GPIO|OUT| |Status1 LED Green (0=ON, 1=OFF)|
|LED|PE13|MCU\_LED1\_R|GPIO|OUT| |Status1 LED Red (0=ON, 1=OFF)|
|LED|PE14|MCU\_LED2\_G|GPIO|OUT| |Status2 LED Green (0=ON, 1=OFF)|
|LED|PE15|MCU\_LED2\_R|GPIO|OUT| |Status2 LED Red (0=ON, 1=OFF)|
|INIT SWITCH|PF11|MCU\_INITSW\_N|GPIO|IRQ IN|external PU|INIT SWITCH (0=ON, 1=OFF)|
|DIP SWITCH|PF12|MCU\_DIPSW0|GPIO|IN|external PD|DIPSW[0] (0=OFF, 1=ON (注意：出力に設定すると壊れます))|
|DIP SWITCH|PF13|MCU\_DIPSW1|GPIO|IN|external PD|DIPSW[1] (0=OFF, 1=ON (注意：出力に設定すると壊れます))|
|DIP SWITCH|PF14|MCU\_DIPSW2|GPIO|IN|external PD|DIPSW[2] (0=OFF, 1=ON (注意：出力に設定すると壊れます))|
|MCU\_BOOT0|PF15|BOOT0/MCU\_DIPSW3|GPIO|IN|external PD|Boot mode[0] (0=Flash Boot, 1=RAM Boot) (boot up sequence)|
|DIP SITCH|:::|:::|:::|:::|:::|DIPSW[3] (0=OFF, 1=ON) (After boot up) (注意：出力に設定すると壊れます)|
|System|PB2|BOOT1|GPIO|IN|external PD|Boot mode[1] = Always 0|
|DIN|PI4|DIO\_IN0|GPIO|IN|external PU|DIN[0] (0=ON, 1=OFF (Default OFF))|
|DIN|PI5|DIO\_IN1|GPIO|IN|external PU|DIN[1] (0=ON, 1=OFF)|
|DIN|PI6|DIO\_IN2|GPIO|IN|external PU|DIN[2] (0=ON, 1=OFF)|
|DIN|PI7|DIO\_IN3|GPIO|IN|external PU|DIN[3] (0=ON, 1=OFF)|
|DOUT|PE3|DIO\_DO0|GPIO|OUT|external PU|DOUT[0] (0=ON, 1=OFF (Default OFF))|
|DOUT|PE4|DIO\_DO1|GPIO|OUT|external PU|DOUT[1] (0=ON, 1=OFF)|
|DOUT|PE5|DIO\_DO2|GPIO|OUT|external PU|DOUT[2] (0=ON, 1=OFF (Photo-MOS RELAY OUT))|
|DOUT|PE6|DIO\_DO3|GPIO|OUT|external PU|DOUT[3] (0=ON, 1=OFF (Photo-MOS RELAY OUT))|
|XIO|PA0|XIO\_PA0\_WKUP|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : ON/SLEEP# status (0=Sleep mode, 1=Wake up)|
|XIO|PA3|XIO\_PA3\_ADC|GPIO|OUT| |XBee S2B/S2C : DTR#/SLEEP\_RQ control (0=Wake up, 1=Pin sleep request)|
|XIO|PA4|SPI1\_NSS|AF5|OUT| |XBee S2B : Not used / S2C : SPI\_NSSEL|
|XIO|PA5|SPI1\_SCK|AF5|OUT| |XBee S2B : Not used / S2C : SPI\_CLK|
|XIO|PA6|SPI1\_MISO|AF5|IN|Internal Pull-UP|XBee S2B : Not used / S2C : SPI\_MISO|
|XIO|PB5|SPI1\_MOSI|AF5|OUT| |XBee S2B : Not used / S2C : SPI\_MOSI|
|XIO|PB8|I2C1\_SCL|AF4|OUT|Internal Pull-UP|Not used[(XBで未使用のピンはGPIO-IN, Internal Pull-UPの設定でも可)]|
|XIO|PB9|I2C1\_SDA|AF4|I/O|Internal Pull-UP|Not used|
|XIO|PB14|OTG\_HS\_DM|AF12|I/O|Internal Pull-UP|Not used|
|XIO|PB15|OTG\_HS\_DP|AF12|I/O|Internal Pull-UP|Not used|
|XIO|PC0|XIO\_PC0\_ADC|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : Associate LED[Green] status (Default)[(XBee moduleのAssociate LED機能をOFFにしてXBee[DIO5]=Inputとすることで、MCUからAssociate LEDの制御が可能となる。MCU[PC0]=GPIO OUT (0=ON, 1=OFF))]|
|XIO|PC6|XIO\_PC6|GPIO|OUT| |XBee S2B/S2C : RESET# control (0=Reset ON, 1=Reset OFF (Default OFF))|
|XIO|PC7|XIO\_PC7|GPIO|OUT| |XBee S2B/S2C : Power Enable (OPTION未実装) (0=OFF, 1=ON (Default ON))|
|XIO|PD3|USART2\_CTS|AF7|IN|Internal Pull-UP|XBee S2B/S2C : CTS# output|
|XIO|PD4|USART2\_RTS|AF7|OUT| |XBee S2B/S2C : RTS# input|
|XIO|PD5|USART2\_TX|AF7|OUT| |XBee S2B/S2C : DIN (serial rxd)|
|XIO|PD6|USART2\_RX|AF7|IN|Internal Pull-UP|XBee S2B/S2C : DOUT (serial txd)|
|XIO|PD7|USART2\_CK|GPIO|IN|Internal Pull-UP|Not used|
|XIO|PE8|XIO\_PE8|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : Commissioning Button status (0=ON, 1=OFF)|
|XIO|PE9|XIO\_PE9|GPIO|IN|Internal Pull-UP|XBee S2B : Not used / S2C : SPI\_ATTN#|
|XIO|PF3|XIO\_PF3\_ADC|GPIO|IN|Internal Pull-Down|XBee S2B/S2C : RSSI LED status (Default)[(XBee moduleのRSSI LED機能をOFFにしてXBee[DIO10]=Inputとすることで、MCUからRSSI LEDの制御が可能となる。MCU[PF3]=GPIO OUT (0=OFF, 1=ON))]|
|XIO|PH11|XIO\_PH11|GPIO|IN|Internal Pull-UP|XBee S2B/S2C : DIO11/LED1[RED] control (通常は使用しない)|
|XIO|PH12|XIO\_PH12|GPIO|IN|Internal Pull-UP|Not used|
|Unused PIN|PG12|USART6\_RTS|GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PG15|USART6\_CTS|GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PC13|RTC\_AF1|GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PI8|RTC\_AF2|GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PD10| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PD13| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PD14| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PD15| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PE0| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PE1| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PE7| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PF2| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PG0| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PG1| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PG2| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PG3| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PG4| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PG5| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PH7| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PH8| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PH9| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PH12| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PH13| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PH14| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PH15| |GPIO|IN|Internal Pull-Down|Not used|
|Unused PIN|PI10| |GPIO|IN|Internal Pull-Down|Not used|

~~REFNOTES~~