この文書の現在のバージョンと選択したバージョンの差分を表示します。
両方とも前のリビジョン 前のリビジョン 次のリビジョン | 前のリビジョン | ||
mae3xx_tips:use_ups:start [2014/11/18 10:43] admin [UPS の選択] |
mae3xx_tips:use_ups:start [2017/11/17 13:07] (現在) admin |
||
---|---|---|---|
ライン 1: | ライン 1: | ||
+ | ====== UPS との接続 (APC) ====== | ||
+ | |||
+ | SD カードや USB HDD などを接続して、ロガーとして運用する場合など、UPS と連動させたい場合もあると思います。\\ | ||
+ | 電源断時にシャットダウン処理などができるよう、UPS と接続する方法を紹介します。 | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ===== UPS の選択 ===== | ||
+ | |||
+ | * Ubuntu Linux で標準でパッケージが用意されている | ||
+ | * ドキュメントも豊富 | ||
+ | |||
+ | という理由から、[[http://www.apc.com/products/category.cfm?id=13&ISOCountryCode=jp|APC]] 社の UPS を使用します。 | ||
+ | |||
+ | [[http://www.apc.com/products/category.cfm?id=13&ISOCountryCode=jp|{{:mae3xx_tips:use_ups:ups-apc.png?400|UPS と言えば APC、マジでおすすめ}}]] | ||
+ | |||
+ | \\ | ||
+ | |||
+ | 製品の種類はたくさんありますが、 | ||
+ | * MA-E3xx は、PC ほど消費電力は大きくない | ||
+ | * 正弦波出力のほうが安心 | ||
+ | といった理由から、[[http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT500J&total_watts=50&tab=models|Smart-UPS]] シリーズの中の、容量が一番小さな製品 (Smart-UPS 500) を使ってみます ((手持ちの旧型機で写真のものとは異なるものを使っています))。 | ||
+ | |||
+ | \\ | ||
+ | |||
+ | **※注** 現行品は、Ubuntu 14.04 の apcupsd (3.14.10) と製品添付のシリアルケーブル (940-0625A) の組み合わせでは動作しません(([[http://apcupsd-ups-control-software.10985.n7.nabble.com/apcupsd-can-t-connect-to-the-UPS-serial-td8623.html|apcupsd can't connect to the UPS (serial)]]))。 | ||
+ | * UPS 本体ファームウェアの更新 | ||
+ | * [参考] [[http://www.schneider-electric.us/sites/us/en/support/faq/faq_main.page?page=content&country=ITB&lang=EN&id=FA164737&redirect=true|How do I update the firmware of my SMT, SMX, SMC, or SRT series Smart-UPS?]] | ||
+ | * UPS **"modbus"** プロトコルの有効化 (本体パネルでの操作) | ||
+ | * apcupsd 3.14.12 への upgrade (v2.4.2α2 で、Ubuntu 15.04α から backport しています) | ||
+ | が必要です。 | ||
+ | |||
+ | {{:mae3xx_tips:use_ups:smart-ups_500.jpg|Smart-UPS 500}} | ||
+ | |||
+ | \\ | ||
+ | ===== 設定 ===== | ||
+ | |||
+ | ==== MA-E3xx との接続 ==== | ||
+ | |||
+ | USB ケーブルで、UPS と接続します。\\ | ||
+ | HID driver で認識されます。 | ||
+ | |||
+ | <code> | ||
+ | [56980.932837] usb 1-1.3: new low-speed USB device number 5 using musb-hdrc | ||
+ | [56981.032473] usb 1-1.3: New USB device found, idVendor=051d, idProduct=0002 | ||
+ | [56981.032513] usb 1-1.3: New USB device strings: Mfr=3, Product=1, SerialNumber=2 | ||
+ | [56981.032523] usb 1-1.3: Product: Smart-UPS 500 FW:650.13.A USB FW:4.2 | ||
+ | [56981.032531] usb 1-1.3: Manufacturer: American Power Conversion | ||
+ | [56981.032538] usb 1-1.3: SerialNumber: AS06xxxxxxxx | ||
+ | </code> | ||
+ | |||
+ | ※ シリアルケーブル (940-0625A 等) で接続する場合、上記ログは出力されません。 | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ==== 設定ファイルの編集 ==== | ||
+ | |||
+ | APC 社の UPS と連動するためのソフト apcupsd はパッケージからインストール済みですので、\\ | ||
+ | 設定ファイルの編集だけを行います。 | ||
+ | |||
+ | 参考: | ||
+ | * [[https://help.ubuntu.com/community/apcupsd|apcupsd - Ubuntu Community Help Wiki]] | ||
+ | * [[http://mizupc8.bio.mie-u.ac.jp/pukiwiki/?apcupsd|apcupsd - PukiWiki]] | ||
+ | |||
+ | /etc/apcupsd/apcupsd.conf を編集します。 | ||
+ | |||
+ | <file config apcupsd.conf> | ||
+ | ## apcupsd.conf v1.1 ## | ||
+ | # | ||
+ | # for apcupsd release 3.14.12 (29 March 2014) - debian | ||
+ | # | ||
+ | # "apcupsd" POSIX config file | ||
+ | |||
+ | # | ||
+ | # ========= General configuration parameters ============ | ||
+ | # | ||
+ | |||
+ | # UPSNAME xxx | ||
+ | # Use this to give your UPS a name in log files and such. This | ||
+ | # is particulary useful if you have multiple UPSes. This does not | ||
+ | # set the EEPROM. It should be 8 characters or less. | ||
+ | #UPSNAME | ||
+ | |||
+ | # UPSCABLE <cable> | ||
+ | # Defines the type of cable connecting the UPS to your computer. | ||
+ | # | ||
+ | # Possible generic choices for <cable> are: | ||
+ | # simple, smart, ether, usb | ||
+ | # | ||
+ | # Or a specific cable model number may be used: | ||
+ | # 940-0119A, 940-0127A, 940-0128A, 940-0020B, | ||
+ | # 940-0020C, 940-0023A, 940-0024B, 940-0024C, | ||
+ | # 940-1524C, 940-0024G, 940-0095A, 940-0095B, | ||
+ | # 940-0095C, 940-0625A, M-04-02-2000 | ||
+ | # | ||
+ | UPSCABLE 940-0625A | ||
+ | |||
+ | # To get apcupsd to work, in addition to defining the cable | ||
+ | # above, you must also define a UPSTYPE, which corresponds to | ||
+ | # the type of UPS you have (see the Description for more details). | ||
+ | # You must also specify a DEVICE, sometimes referred to as a port. | ||
+ | # For USB UPSes, please leave the DEVICE directive blank. For | ||
+ | # other UPS types, you must specify an appropriate port or address. | ||
+ | # | ||
+ | # UPSTYPE DEVICE Description | ||
+ | # apcsmart /dev/tty** Newer serial character device, appropriate for | ||
+ | # SmartUPS models using a serial cable (not USB). | ||
+ | # | ||
+ | # usb <BLANK> Most new UPSes are USB. A blank DEVICE | ||
+ | # setting enables autodetection, which is | ||
+ | # the best choice for most installations. | ||
+ | # | ||
+ | # net hostname:port Network link to a master apcupsd through apcupsd's | ||
+ | # Network Information Server. This is used if the | ||
+ | # UPS powering your computer is connected to a | ||
+ | # different computer for monitoring. | ||
+ | # | ||
+ | # snmp hostname:port:vendor:community | ||
+ | # SNMP network link to an SNMP-enabled UPS device. | ||
+ | # Hostname is the ip address or hostname of the UPS | ||
+ | # on the network. Vendor can be can be "APC" or | ||
+ | # "APC_NOTRAP". "APC_NOTRAP" will disable SNMP trap | ||
+ | # catching; you usually want "APC". Port is usually | ||
+ | # 161. Community is usually "private". | ||
+ | # | ||
+ | # netsnmp hostname:port:vendor:community | ||
+ | # OBSOLETE | ||
+ | # Same as SNMP above but requires use of the | ||
+ | # net-snmp library. Unless you have a specific need | ||
+ | # for this old driver, you should use 'snmp' instead. | ||
+ | # | ||
+ | # dumb /dev/tty** Old serial character device for use with | ||
+ | # simple-signaling UPSes. | ||
+ | # | ||
+ | # pcnet ipaddr:username:passphrase:port | ||
+ | # PowerChute Network Shutdown protocol which can be | ||
+ | # used as an alternative to SNMP with the AP9617 | ||
+ | # family of smart slot cards. ipaddr is the IP | ||
+ | # address of the UPS management card. username and | ||
+ | # passphrase are the credentials for which the card | ||
+ | # has been configured. port is the port number on | ||
+ | # which to listen for messages from the UPS, normally | ||
+ | # 3052. If this parameter is empty or missing, the | ||
+ | # default of 3052 will be used. | ||
+ | # | ||
+ | # modbus /dev/tty** Serial device for use with newest SmartUPS models | ||
+ | # supporting the MODBUS protocol. | ||
+ | # | ||
+ | UPSTYPE modbus | ||
+ | DEVICE /dev/ttyO1 | ||
+ | |||
+ | # POLLTIME <int> | ||
+ | # Interval (in seconds) at which apcupsd polls the UPS for status. This | ||
+ | # setting applies both to directly-attached UPSes (UPSTYPE apcsmart, usb, | ||
+ | # dumb) and networked UPSes (UPSTYPE net, snmp). Lowering this setting | ||
+ | # will improve apcupsd's responsiveness to certain events at the cost of | ||
+ | # higher CPU utilization. The default of 60 is appropriate for most | ||
+ | # situations. | ||
+ | #POLLTIME 60 | ||
+ | |||
+ | # LOCKFILE <path to lockfile> | ||
+ | # Path for device lock file. Not used on Win32. | ||
+ | LOCKFILE /var/lock | ||
+ | |||
+ | # SCRIPTDIR <path to script directory> | ||
+ | # Directory in which apccontrol and event scripts are located. | ||
+ | SCRIPTDIR /etc/apcupsd | ||
+ | |||
+ | # PWRFAILDIR <path to powerfail directory> | ||
+ | # Directory in which to write the powerfail flag file. This file | ||
+ | # is created when apcupsd initiates a system shutdown and is | ||
+ | # checked in the OS halt scripts to determine if a killpower | ||
+ | # (turning off UPS output power) is required. | ||
+ | PWRFAILDIR /etc/apcupsd | ||
+ | |||
+ | # NOLOGINDIR <path to nologin directory> | ||
+ | # Directory in which to write the nologin file. The existence | ||
+ | # of this flag file tells the OS to disallow new logins. | ||
+ | NOLOGINDIR /etc | ||
+ | |||
+ | |||
+ | # | ||
+ | # ======== Configuration parameters used during power failures ========== | ||
+ | # | ||
+ | |||
+ | # The ONBATTERYDELAY is the time in seconds from when a power failure | ||
+ | # is detected until we react to it with an onbattery event. | ||
+ | # | ||
+ | # This means that, apccontrol will be called with the powerout argument | ||
+ | # immediately when a power failure is detected. However, the | ||
+ | # onbattery argument is passed to apccontrol only after the | ||
+ | # ONBATTERYDELAY time. If you don't want to be annoyed by short | ||
+ | # powerfailures, make sure that apccontrol powerout does nothing | ||
+ | # i.e. comment out the wall. | ||
+ | ONBATTERYDELAY 6 | ||
+ | |||
+ | # | ||
+ | # Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so | ||
+ | # the first that occurs will cause the initation of a shutdown. | ||
+ | # | ||
+ | |||
+ | # If during a power failure, the remaining battery percentage | ||
+ | # (as reported by the UPS) is below or equal to BATTERYLEVEL, | ||
+ | # apcupsd will initiate a system shutdown. | ||
+ | BATTERYLEVEL 5 | ||
+ | |||
+ | # If during a power failure, the remaining runtime in minutes | ||
+ | # (as calculated internally by the UPS) is below or equal to MINUTES, | ||
+ | # apcupsd, will initiate a system shutdown. | ||
+ | MINUTES 3 | ||
+ | |||
+ | # If during a power failure, the UPS has run on batteries for TIMEOUT | ||
+ | # many seconds or longer, apcupsd will initiate a system shutdown. | ||
+ | # A value of 0 disables this timer. | ||
+ | # | ||
+ | # Note, if you have a Smart UPS, you will most likely want to disable | ||
+ | # this timer by setting it to zero. That way, you UPS will continue | ||
+ | # on batteries until either the % charge remaing drops to or below BATTERYLEVEL, | ||
+ | # or the remaining battery runtime drops to or below MINUTES. Of course, | ||
+ | # if you are testing, setting this to 60 causes a quick system shutdown | ||
+ | # if you pull the power plug. | ||
+ | # If you have an older dumb UPS, you will want to set this to less than | ||
+ | # the time you know you can run on batteries. | ||
+ | TIMEOUT 0 | ||
+ | |||
+ | # Time in seconds between annoying users to signoff prior to | ||
+ | # system shutdown. 0 disables. | ||
+ | ANNOY 300 | ||
+ | |||
+ | # Initial delay after power failure before warning users to get | ||
+ | # off the system. | ||
+ | ANNOYDELAY 60 | ||
+ | |||
+ | # The condition which determines when users are prevented from | ||
+ | # logging in during a power failure. | ||
+ | # NOLOGON <string> [ disable | timeout | percent | minutes | always ] | ||
+ | NOLOGON disable | ||
+ | |||
+ | # If KILLDELAY is non-zero, apcupsd will continue running after a | ||
+ | # shutdown has been requested, and after the specified time in | ||
+ | # seconds attempt to kill the power. This is for use on systems | ||
+ | # where apcupsd cannot regain control after a shutdown. | ||
+ | # KILLDELAY <seconds> 0 disables | ||
+ | KILLDELAY 0 | ||
+ | |||
+ | # | ||
+ | # ==== Configuration statements for Network Information Server ==== | ||
+ | # | ||
+ | |||
+ | # NETSERVER [ on | off ] on enables, off disables the network | ||
+ | # information server. If netstatus is on, a network information | ||
+ | # server process will be started for serving the STATUS and | ||
+ | # EVENT data over the network (used by CGI programs). | ||
+ | NETSERVER on | ||
+ | |||
+ | # NISIP <dotted notation ip address> | ||
+ | # IP address on which NIS server will listen for incoming connections. | ||
+ | # This is useful if your server is multi-homed (has more than one | ||
+ | # network interface and IP address). Default value is 0.0.0.0 which | ||
+ | # means any incoming request will be serviced. Alternatively, you can | ||
+ | # configure this setting to any specific IP address of your server and | ||
+ | # NIS will listen for connections only on that interface. Use the | ||
+ | # loopback address (127.0.0.1) to accept connections only from the | ||
+ | # local machine. | ||
+ | NISIP 127.0.0.1 | ||
+ | |||
+ | # NISPORT <port> default is 3551 as registered with the IANA | ||
+ | # port to use for sending STATUS and EVENTS data over the network. | ||
+ | # It is not used unless NETSERVER is on. If you change this port, | ||
+ | # you will need to change the corresponding value in the cgi directory | ||
+ | # and rebuild the cgi programs. | ||
+ | NISPORT 3551 | ||
+ | |||
+ | # If you want the last few EVENTS to be available over the network | ||
+ | # by the network information server, you must define an EVENTSFILE. | ||
+ | EVENTSFILE /var/log/apcupsd.events | ||
+ | |||
+ | # EVENTSFILEMAX <kilobytes> | ||
+ | # By default, the size of the EVENTSFILE will be not be allowed to exceed | ||
+ | # 10 kilobytes. When the file grows beyond this limit, older EVENTS will | ||
+ | # be removed from the beginning of the file (first in first out). The | ||
+ | # parameter EVENTSFILEMAX can be set to a different kilobyte value, or set | ||
+ | # to zero to allow the EVENTSFILE to grow without limit. | ||
+ | EVENTSFILEMAX 10 | ||
+ | |||
+ | # | ||
+ | # ========== Configuration statements used if sharing ============= | ||
+ | # a UPS with more than one machine | ||
+ | |||
+ | # | ||
+ | # Remaining items are for ShareUPS (APC expansion card) ONLY | ||
+ | # | ||
+ | |||
+ | # UPSCLASS [ standalone | shareslave | sharemaster ] | ||
+ | # Normally standalone unless you share an UPS using an APC ShareUPS | ||
+ | # card. | ||
+ | UPSCLASS standalone | ||
+ | |||
+ | # UPSMODE [ disable | share ] | ||
+ | # Normally disable unless you share an UPS using an APC ShareUPS card. | ||
+ | UPSMODE disable | ||
+ | |||
+ | # | ||
+ | # ===== Configuration statements to control apcupsd system logging ======== | ||
+ | # | ||
+ | |||
+ | # Time interval in seconds between writing the STATUS file; 0 disables | ||
+ | STATTIME 0 | ||
+ | |||
+ | # Location of STATUS file (written to only if STATTIME is non-zero) | ||
+ | STATFILE /var/log/apcupsd.status | ||
+ | |||
+ | # LOGSTATS [ on | off ] on enables, off disables | ||
+ | # Note! This generates a lot of output, so if | ||
+ | # you turn this on, be sure that the | ||
+ | # file defined in syslog.conf for LOG_NOTICE is a named pipe. | ||
+ | # You probably do not want this on. | ||
+ | LOGSTATS off | ||
+ | |||
+ | # Time interval in seconds between writing the DATA records to | ||
+ | # the log file. 0 disables. | ||
+ | DATATIME 0 | ||
+ | |||
+ | # FACILITY defines the logging facility (class) for logging to syslog. | ||
+ | # If not specified, it defaults to "daemon". This is useful | ||
+ | # if you want to separate the data logged by apcupsd from other | ||
+ | # programs. | ||
+ | #FACILITY DAEMON | ||
+ | |||
+ | # | ||
+ | # ========== Configuration statements used in updating the UPS EPROM ========= | ||
+ | # | ||
+ | |||
+ | # | ||
+ | # These statements are used only by apctest when choosing "Set EEPROM with conf | ||
+ | # file values" from the EEPROM menu. THESE STATEMENTS HAVE NO EFFECT ON APCUPSD. | ||
+ | # | ||
+ | |||
+ | # UPS name, max 8 characters | ||
+ | #UPSNAME UPS_IDEN | ||
+ | |||
+ | # Battery date - 8 characters | ||
+ | #BATTDATE mm/dd/yy | ||
+ | |||
+ | # Sensitivity to line voltage quality (H cause faster transfer to batteries) | ||
+ | # SENSITIVITY H M L (default = H) | ||
+ | #SENSITIVITY H | ||
+ | |||
+ | # UPS delay after power return (seconds) | ||
+ | # WAKEUP 000 060 180 300 (default = 0) | ||
+ | #WAKEUP 60 | ||
+ | |||
+ | # UPS Grace period after request to power off (seconds) | ||
+ | # SLEEP 020 180 300 600 (default = 20) | ||
+ | #SLEEP 180 | ||
+ | |||
+ | # Low line voltage causing transfer to batteries | ||
+ | # The permitted values depend on your model as defined by last letter | ||
+ | # of FIRMWARE or APCMODEL. Some representative values are: | ||
+ | # D 106 103 100 097 | ||
+ | # M 177 172 168 182 | ||
+ | # A 092 090 088 086 | ||
+ | # I 208 204 200 196 (default = 0 => not valid) | ||
+ | #LOTRANSFER 208 | ||
+ | |||
+ | # High line voltage causing transfer to batteries | ||
+ | # The permitted values depend on your model as defined by last letter | ||
+ | # of FIRMWARE or APCMODEL. Some representative values are: | ||
+ | # D 127 130 133 136 | ||
+ | # M 229 234 239 224 | ||
+ | # A 108 110 112 114 | ||
+ | # I 253 257 261 265 (default = 0 => not valid) | ||
+ | #HITRANSFER 253 | ||
+ | |||
+ | # Battery charge needed to restore power | ||
+ | # RETURNCHARGE 00 15 50 90 (default = 15) | ||
+ | #RETURNCHARGE 15 | ||
+ | |||
+ | # Alarm delay | ||
+ | # 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never | ||
+ | # BEEPSTATE 0 T L N (default = 0) | ||
+ | #BEEPSTATE T | ||
+ | |||
+ | # Low battery warning delay in minutes | ||
+ | # LOWBATT 02 05 07 10 (default = 02) | ||
+ | #LOWBATT 2 | ||
+ | |||
+ | # UPS Output voltage when running on batteries | ||
+ | # The permitted values depend on your model as defined by last letter | ||
+ | # of FIRMWARE or APCMODEL. Some representative values are: | ||
+ | # D 115 | ||
+ | # M 208 | ||
+ | # A 100 | ||
+ | # I 230 240 220 225 (default = 0 => not valid) | ||
+ | #OUTPUTVOLTS 230 | ||
+ | |||
+ | # Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on | ||
+ | # SELFTEST 336 168 ON OFF (default = 336) | ||
+ | #SELFTEST 336 | ||
+ | </file> | ||
+ | |||
+ | 変更した点は下記になります (conf ファイル中に書いてあるドキュメントのままですが)。 | ||
+ | |||
+ | ^ 項目 ^ 初期値 ^ 設定値 ^^ | ||
+ | ^:::^:::^ USB接続 ^ シリアルケーブル ^ | ||
+ | |UPSCABLE| smart | usb | 940-0625A | | ||
+ | |UPSTYPE| apcsmart | usb | modbus | | ||
+ | |DEVICE| /dev/ttyS0 | "" (空欄) | /dev/ttyO1 | | ||
+ | |||
+ | \\ | ||
+ | |||
+ | Ubuntu の daemon が起動時に参照するファイル (/etc/default/apcupsd) も変更します。 | ||
+ | |||
+ | <file conf apcupsd> | ||
+ | # Defaults for apcupsd initscript | ||
+ | |||
+ | # Apcupsd-devel internal configuration | ||
+ | APCACCESS=/sbin/apcaccess | ||
+ | ISCONFIGURED=yes | ||
+ | </file> | ||
+ | |||
+ | ISCONFIGURED を "no" から "yes" に変更します。 | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ===== apcupsd の起動 ===== | ||
+ | |||
+ | 設定ファイルの編集ができたら、service を起動します。 | ||
+ | |||
+ | <code> | ||
+ | user1@plum:~$ sudo service apcupsd start | ||
+ | Starting UPS power management: apcupsd. | ||
+ | user1@plum:~$ | ||
+ | </code> | ||
+ | |||
+ | \\ | ||
+ | |||
+ | MA-E3xx の起動時にデフォルトで起動させるためには、update-rc.d コマンドで有効化します。 | ||
+ | |||
+ | <code> | ||
+ | user1@plum:~$ sudo update-rc.d apcupsd enable | ||
+ | update-rc.d: warning: start runlevel arguments (none) do not match apcupsd Default-Start values (2 3 4 5) | ||
+ | update-rc.d: warning: stop runlevel arguments (none) do not match apcupsd Default-Stop values (0 1 6) | ||
+ | Enabling system startup links for /etc/init.d/apcupsd ... | ||
+ | Removing any system startup links for /etc/init.d/apcupsd ... | ||
+ | /etc/rc0.d/K80apcupsd | ||
+ | /etc/rc1.d/S41apcupsd | ||
+ | /etc/rc2.d/K59apcupsd | ||
+ | /etc/rc3.d/K59apcupsd | ||
+ | /etc/rc4.d/K59apcupsd | ||
+ | /etc/rc5.d/K59apcupsd | ||
+ | /etc/rc6.d/K80apcupsd | ||
+ | Adding system startup for /etc/init.d/apcupsd ... | ||
+ | /etc/rc0.d/K80apcupsd -> ../init.d/apcupsd | ||
+ | /etc/rc1.d/S41apcupsd -> ../init.d/apcupsd | ||
+ | /etc/rc6.d/K80apcupsd -> ../init.d/apcupsd | ||
+ | /etc/rc2.d/S41apcupsd -> ../init.d/apcupsd | ||
+ | /etc/rc3.d/S41apcupsd -> ../init.d/apcupsd | ||
+ | /etc/rc4.d/S41apcupsd -> ../init.d/apcupsd | ||
+ | /etc/rc5.d/S41apcupsd -> ../init.d/apcupsd | ||
+ | user1@plum:~$ | ||
+ | </code> | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ===== UPSの状態確認 ===== | ||
+ | |||
+ | UPS の状態を確認することができます。 | ||
+ | |||
+ | <code> | ||
+ | user1@plum:~$ sudo service apcupsd status | ||
+ | APC : 001,036,0846 | ||
+ | DATE : 2014-11-18 10:58:39 +0900 | ||
+ | HOSTNAME : plum | ||
+ | VERSION : 3.14.12 (29 March 2014) debian | ||
+ | UPSNAME : APCUPS | ||
+ | CABLE : Custom Cable Smart | ||
+ | DRIVER : MODBUS UPS Driver | ||
+ | UPSMODE : Stand Alone | ||
+ | STARTTIME: 2014-11-18 10:51:09 +0900 | ||
+ | MODEL : Smart-UPS 500 | ||
+ | STATUS : ONLINE | ||
+ | LINEV : 103.6 Volts | ||
+ | LOADPCT : 0.0 Percent | ||
+ | BCHARGE : 100.0 Percent | ||
+ | TIMELEFT : 383.0 Minutes | ||
+ | MBATTCHG : 5 Percent | ||
+ | MINTIMEL : 3 Minutes | ||
+ | MAXTIME : 0 Seconds | ||
+ | OUTPUTV : 103.6 Volts | ||
+ | DWAKE : 0 Seconds | ||
+ | DSHUTD : 90 Seconds | ||
+ | ITEMP : 34.6 C | ||
+ | BATTV : 26.8 Volts | ||
+ | LINEFREQ : 50.0 Hz | ||
+ | NUMXFERS : 0 | ||
+ | TONBATT : 0 Seconds | ||
+ | CUMONBATT: 0 Seconds | ||
+ | XOFFBATT : N/A | ||
+ | SELFTEST : OK | ||
+ | STATFLAG : 0x05000008 | ||
+ | MANDATE : 2013-09-20 | ||
+ | SERIALNO : AS133xxxxxxx | ||
+ | BATTDATE : 2014-09-15 | ||
+ | NOMOUTV : 100 Volts | ||
+ | NOMPOWER : 360 Watts | ||
+ | FIRMWARE : UPS 09.1 / 00.4 | ||
+ | END APC : 2014-11-18 10:59:38 +0900 | ||
+ | user1@plum:~$ | ||
+ | </code> | ||